|
|
|
|
|
|
|
|
|
|
|
Hotpoint washing machine flashing H20 error?Washing machine Hotpoint WF860 flashing up H20, water is getting into to drum but will not empty and finish cycle, water was also leaking from the front detergent drawer. Do you know how I can fix it?
Leigh Anne Cammack December 2007
|
|
|
Click here if you can answer this question |
|
|
|
|
|
My washing machine stops h2o warning sign, what does that mesn
Shui October 2016 |
|
|
|
|
|
|
|
|
My machine came up with the H20 it turned out that the motor bushes had gone so i would definitely check this first. not a expensive board fault
Ryan August 2015 |
|
|
|
|
|
|
|
|
H20 error now water coming out,model WWPF 762 help!!!!
Nat July 2015 |
|
|
|
|
|
|
|
|
Had 'H2O' error with machine not emptying and not operating. Eventually drained itself. Took off top (2 self tappers at back), push top back. Clear plastic tube behind soap drawer had become disconnected. Refitted using pliers to release clip first (might be advisable to add a thick cable tie). Switched off and then on again. Short cycle then drained. Repeated again. Checked inlet pipe and waste working (hold onto to feel flow). Message went and now fixed. Mine was clear but also worth also checking the filter to outlet pipe as a sock or tissue (or build of fluff) can block. Naturally do not touch inside without disconnecting power first.
Jeff February 2015 |
|
|
|
|
|
|
|
|
if all above fails replace the main control board
hotpoint man July 2013 |
|
|
|
|
|
|
|
|
Brain the size of a pea. I was closing the valve not opening!
Allen November 2012 |
|
|
|
|
|
|
|
|
I have the same problem with my washing machine, i thought i check some forums before ordering a new inner valve ... dont buy a inner valve !! ... its definitely the clear tube behind the soap draw ... thanks everyone for you much appreciated help !!!
Dela March 2012 |
|
|
|
|
|
|
|
|
Brand new machine , powered up and after a short while H20 flashed up . Turned out the inlet filler pipe must have been partialy kinked when I pushed the machine into position , restricting the correct amount of water to start the wash . I could see water entering the machine but it wasn't enough . I tried it again after carefully pushing the machine back and it was fine....
nigel the sparky June 2011 |
|
|
|
|
|
|
|
|
Our washing machine kept just filling up with water, H20 actually means no water was going in. We unblocked the filter at the bottom of the drum where all the crap is. Now works perfectly.
Lisa May 2011 |
|
|
|
|
|
|
|
|
My machine is fu**ed... said H20 error, I tried doing somethings you lot said now it doesn't even switch on. Nice one...!
Washing machine idiot June 2010 |
|
|
|
|
|
|
|
|
defo the tube loose, i found this out after buying a new inlet valve costing me £25 , grrrrr, thanks for the advise!!
jonathon preece May 2010 |
|
|
|
|
|
|
|
|
Thanks mutley cat. big help
paul taylor April 2010 |
|
|
|
|
|
|
|
|
this really works was just about to buy a new washers as i thought it might be a big job , took off lid put my hand under soap draw and switch component clicked back into place .
mutley cat March 2010 |
|
|
|
|
|
|
|
|
get a new one lol
jj August 2009 |
|
|
|
|
|
|
|
|
washing machine will fill,when it stops filling about 2minutes later it will flash h20 and will not do anything else.
ms farrar July 2009 |
|
|
|
|
|
|
|
|
I had the exact same error and the drum would over fill and pore out from the soap drawer, but this resolved it.
the vaccum switch not connected. Remove lid. Just behind soap drawer is a round component with a clear tube conected to the bottom of it. check it hasn.t come adrift.
Mine had come adrift re-connected and working fine.
Tel April 2009 |
|
|
|
|
|
|
|
|
could be overfilling. could be vaccum switch not connected. Remove lid. Just behind soap drawer is a round component with a clear tube conected to the bottom of it. check it hasn.t come adrift. Also if paddles have been replaced. check where filler hose meets drum for any clothing that might have slipped through previously. good luck
sidthedog April 2008 |
|
|
|
|
|
|
|
|
I recently had the same problem with my Hotpoint Ultima WF860P and after some investigations, I found a disconnected tube linked to the pressure switch beneath the top cover was the cause of the problem. In short, this tube forces air to the pressure switch and cuts off the valve feeds.
Andrew Algar - Brighton March 2008 |
|
|
|
|
|
|
|
|
drain filter possibly blocked or pump blocked when spinning this throws the water back up into the powder drawer very alarming to see I think the filter is behind the front kick plate to empty machine place drain hose in a bowl lower to floor does it flow fast or slow if slow sump filter /pump blocked manually empty the machine into the bowl remove front kick plate unscrew filter NOTE there will still be water behind the blockage clean filter and pump reassemble make sure pump impeller is free to turn if not a new pump is needed
wirecutterman December 2007 |
|
|
|
|
|
|
|
|
Add your answer using the form below ...
|
|
|
|
|
|
|
|
|
|
|
|
|
|